ZX Spectrum+

After the well known ‘rubber keyed’ Spectrum came the ZX Spectrum+.  I never encountered one during my childhood, probably because they came out a little later, but also because I was perfectly happy with my 48K.  The Spectrum+ is basically a 48K with a ‘proper’ keyboard – nothing wrong with the ‘rubber keys’ ;). Either way I wanted one for my collection, so off to Ebay again, and it wasn’t long before a boxed Spectrum+ was sitting on my bench.

ZX Spectrum+ (Issue 6A)

First impressions were that it was in good condition, but very dirty.  Voltages checked out fine, a good sign, but no picture when I plugged it into my TV.  I decided to perform the standard composite upgrade first given my success with this is in past.  And guess what ?  It worked – another dodgy tv out circuit.

Well that was easy.  Now for the standard future proofing, recapping and replacement of the linear power regulator with a switched regulator.

Recapped and new power regulator

As a final upgrade I fixed a heat-sink to the ULA to improve its chances of working for a few more years.  Pleased with that – fully working mint Spectrum+ Issue 6A from 1984.  The only thing left was a good clean, especially of the keyboard.

I knew it was all going too well – on reinstalling, the keyboard membrane completely failed 🙁 Luckily, as with most Spectrum parts, a new membrane was easily sourced on the internet.

Time for some proper testing.

Proper testing

It was now ready to join my others on the Spectrum shelf …

Job complete.

Spectrum finishing touches (part 4)

With both Spectrum’s working I decided on a few upgrades before calling it a day.  Both of the cover plates are beyond fixing so I decided to buy replacements.   The keyboard membrane on the Issue 4 also decided to give-up during the final stages and needed replacing.  Both of these were easy to fit and only took a few minutes.

I decided to upgrade both with switched power regulators.  These are much more efficient and remove the need for the heat-sink.  Spectrum’s are well known for getting warm so anything you can do to reduce this will help future-proofing

With that done I declared them both finished, don’t they look good 🙂

Job done.

Fixing the Issue 2 Spectrum (part 3)

On first inspection the Issue 2 showed a picture with the typical Spectrum coloured border and some flashing bars in the central paper area.  The voltages all looked ok, with the exception of a low -5v line.  Plugging in the diagnostics cartridge wasn’t much help as it didn’t do anything…

Some diagnostics

I decided to tackle the low -5v line first by replacing transistors TR4 and TR5.  This was a simple job and resulted in a slightly better -5v line, but not by much.  With the diagnostics cartridge not being much help I first swapped the ULA, as this was socket-ed, to see if this had any effect. It didn’t.  Knowing that the first thing the Spectrum bios does on boot is set the screen border to white I suspected the Z80 CPU or the bios.  The clock signal was ok, so the CPU should start, and the diagnostics cartridge would by-pass the bios, and that didn’t work, so I was left with the Z80.

Replacing the Z80 was a bigger job, it wasn’t in a socket and as a 40 pin chip was the biggest de-soldering job I had tackled.  Armed with my new de-soldering station and some solder wick I started on the 40 pins.  

With a new socket and Z80 CPU I powered it up, and it did … ish

More diagnostics

The diagnostics cartridge started but hung after the first few steps without outputting a report. At least now the cpu was executing the code from bios (white border on boot).  I tried the ULA from the Issue 4 board and the and the diagnostics cartridge executed correctly…. oh no.  The ULA is the hardest component to replace, off to ebay. Meanwhile the diagnostics cartridge indicated that all of the lower DRAM and a couple of upper RAM chips were toast 🙁  What has this board been through?

Lower RAM removed

I decided to replace the lower DRAM with a modern replacement board.  It’s known to be problematic and a replacement board wouldn’t need the -5v or 12v supplies. With the number of components that this board was going to need replacing it was never going to be ‘original’.  To do this I needed to remove all the lower DRAM chips and replace with sockets.

Nice new sockets for the RAM

I decided to practise my de-soldering and remove all the lower and upper DRAM chips, makes fixing future issues easier.  With this done I replaced the lower DRAM with a modern board from Retroleum and the upper ram with new 64K chips.  The final piece was a Nebula replacement ULA, again from Retroleum.

Diagnostics cartridge

With everything replaces, almost literally, I had a working Issue Spectrum.

All done… only cosmetics next.

Fixing the Issue 4 Spectrum (part 2)

After checking the power rails it was obvious that the 5v regulator wasn’t working, so first action was to replace it.

With the regulator replaced I hopefully tried the power again.  This time all the power rails looked good, but still no picture. After checking with my multi-meter and oscilloscope everything looked good.  Clock signals fine, memory address and data lines ok , ULA video output ok…..  I was at a bit of a loss.

While thinking the problem over I decided to apply the composite video mod in the hope that when it did work at least it would look better.

Composite video mod

With that completed, I plugged in once again to started diagnosing the problem, and surprise …. I had a picture.  So the problem must be with the analog video out.  

I wasn’t out of the woods yet, I had the typical memory fault colour bars on boot.  Using my new diagnostics cartridge quickly identified the two upper DRAM chips that were to blame.

Just a couple of upper memory faults…

The upper DRAM was already socket-ed making replacing very easy.

Fixed Spectrum 48K

With the fix complete it was time to play some games 🙂

Game time

Still some cosmetic fixes, but that’s a later post.

A tale of two Spectrums (Part 1)

Over the last couple of months I have been watching YouTube channels of people fixing various retro computers, mainly Commodore 64’s, BBC B’s and ZX Spectrum’s.   Like many others, my computing career started with the Spectrum, so armed with nostalgia,  some self taught electronics knowledge and a soldering iron I decided to take up the challenge and bring a non-working Spectrum back to its full gaming prowess.

Where to start?

I didn’t want to buy a working Spectrum, where’s the fun in that?  So I hit Ebay looking for ‘untested’ or not working listings.  There are lots listed, the problem became identifying the best of the bad ones and not paying over the top for what could become a costly project.   I set myself a limit of £35 and started bidding.  I lost out on quite a few from the usual last minute automated bids, but eventually won two.

In the post

The Spectrum’s arrived quickly with a random selection of interfaces and game tapes.  The general condition of the units was ‘dirty’, but that was to be expected, with various scuffs and scratches on the keyboard face-plates.  All of which can be sorted with cleaning and/or replacement parts from the various retro/hobbyist websites.

First look at the Spectrums…

Now to see what state they were actually in.  I had watched far too many hours of YouTubers diagnosing faults so I had a good idea where to start, visual inspection first then check the power rails for the correct voltages.

Opening them up

Starting with the visual inspection I opened them up to find an Issue 2 (1982) and Issue 4 (1984) vintage. 

Electrically, both looked fairly ‘clean’, with only one noticeable fix; the Issue 4 board has had upper memory chips replaced at some point in the past.

Powering up

The Spectrum has a couple of peculiarities which it shares with some of the other computers of the same era.  The power supply is provided by a centre negative power jack; this was the first thing to check, didn’t want to start by causing any more damage than was there to start.  Multiple voltages – internally the Spectrum uses 5v, -5v and 12v, if these are incorrect it can cause damage, especially to the lower DRAM chips.

Following a quick check with my multi-meter, the Issue 4 Spectrum was completely dead – 0 volts everywhere except from the input source.  The Issue 2 was a more hopeful with all of the voltages looking OK  – although the -5v was a little low, but within specs.

Optimistically plugging the Issue 2 into a TV, with an analog tuner, resulted in a fuzzy, but recognisable Spectrum border, but cyan not white, with black and white bars in the centre.  I decided to make the standard composite upgrade before further diagnosing to make the job easier, and less fuzzy (shown below).

Issue 2 fault

Next blog, diagnosing the issues and hopefully fixing.